A Gpio_module groups multiple GPIO pins together. More...

#include <vbus_gpio>

Inheritance diagram for L4vbus::Gpio_module:

Collaboration diagram for L4vbus::Gpio_module:

Data Structures
struct	Pin_slice
	A slice of the pins provided by this module. More...

Public Member Functions
int	setup (Pin_slice const &mask, unsigned mode, unsigned value) const
	Configure function of multiple GPIO pins at once.
int	config_pad (Pin_slice const &mask, unsigned func, unsigned value) const
	Hardware specific configuration function for multiple GPIO pins.
int	get (unsigned offset, unsigned *data) const
	Read values of multiple GPIO pins at once.
int	set (Pin_slice const &mask, unsigned data)
	Set multiple GPIO output pins at once.
Gpio_pin	pin (unsigned pin) const
	Get Gpio_pin for a specific pin of this Gpio_module.
Public Member Functions inherited from L4vbus::Device
	Device ()
	Construct a new vbus device using the NULL device L4VBUS_NULL.
	Device (L4::Cap< Vbus > bus, l4vbus_device_handle_t dev)
	Construct a new vbus device using a device handle.
L4::Cap< Vbus >	bus_cap () const
	Access the Vbus capability of the underlying virtual bus.
l4vbus_device_handle_t	dev_handle () const
	Access the device handle of this device.
int	device_by_hid (Device child, char const hid, int depth=L4VBUS_MAX_DEPTH, l4vbus_device_t *devinfo=0) const
	Find a device by the hardware interface identifier (HID).
int	next_device (Device child, int depth=L4VBUS_MAX_DEPTH, l4vbus_device_t devinfo=0) const
	Find next child following child.
int	device (l4vbus_device_t *devinfo) const
	Obtain detailed information about a Vbus device.
int	get_resource (unsigned res_idx, l4vbus_resource_t *res) const
	Obtain the resource description of an individual device resource.
int	is_compatible (char const *cid) const
	Check if the given device has a compatibility ID (CID) or HID that matches cid.
bool	operator== (Device const &o) const
	Test if two devices are the same Vbus device.
bool	operator!= (Device const &o) const
	Test if two Vbus devices are not the same.
Public Member Functions inherited from L4vbus::Pm< Device >
int	pm_suspend () const
	Suspend the device.
int	pm_resume () const
	Resume the device.

Additional Inherited Members
Protected Attributes inherited from L4vbus::Device
L4::Cap< Vbus >	_bus
	The Vbus capability where this device is located on.
l4vbus_device_handle_t	_dev
	The device handle for this device.

Detailed Description

A Gpio_module groups multiple GPIO pins together.

Definition at line 133 of file vbus_gpio.

Member Function Documentation

◆ config_pad()

int L4vbus::Gpio_module::config_pad	(	Pin_slice const &	mask,
		unsigned	func,
		unsigned	value ) const

inline

Hardware specific configuration function for multiple GPIO pins.

Parameters

mask	Mask of GPIO pins to configure. A bit set to 1 configures this pin. A maximum of 32 pins can be configured at once. The real number depends on the hardware and the driver implementation.
func	Hardware specific configuration register, usually offset to the GPIO chip's base address.
value	Value which is written into the hardware specific configuration register for the specified pins

Returns: 0 if OK, error code otherwise

Definition at line 185 of file vbus_gpio.

References L4vbus::Device::_bus, L4vbus::Device::_dev, and l4vbus_gpio_multi_config_pad().

Here is the call graph for this function:

◆ get()

int L4vbus::Gpio_module::get	(	unsigned	offset,
		unsigned *	data ) const

inline

Read values of multiple GPIO pins at once.

Parameters

	offset	Pin corresponding to the LSB in data. Note: allowed may be hardware specific.
[out]	data	Each bit returns the value (0 or 1) for the corresponding GPIO pin. The value of pins that are not accessible is undefined.

Returns: 0 if OK, error code otherwise

Definition at line 201 of file vbus_gpio.

References L4vbus::Device::_bus, L4vbus::Device::_dev, and l4vbus_gpio_multi_get().

Here is the call graph for this function:

◆ pin()

Gpio_pin L4vbus::Gpio_module::pin ( unsigned pin ) const

inline

Get Gpio_pin for a specific pin of this Gpio_module.

Parameters

pin	GPIO pin number to get Gpio_pin for.

Returns: Gpio_pin

Definition at line 229 of file vbus_gpio.

References pin().

Referenced by pin().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ set()

int L4vbus::Gpio_module::set	(	Pin_slice const &	mask,
		unsigned	data )

inline

Set multiple GPIO output pins at once.

Parameters

mask	Mask of GPIO pins to set. A bit set to 1 selects this pin. A maximum of 32 pins can be set at once. The real number depends on the hardware and the driver implementation.
data	Each bit corresponds to the GPIO pin in mask. The value of each bit is written to the GPIO pin if its bit in mask is set.

Returns: 0 if OK, error code otherwise

Definition at line 217 of file vbus_gpio.

References L4vbus::Device::_bus, L4vbus::Device::_dev, and l4vbus_gpio_multi_set().

Here is the call graph for this function:

◆ setup()

int L4vbus::Gpio_module::setup	(	Pin_slice const &	mask,
		unsigned	mode,
		unsigned	value ) const

inline

Configure function of multiple GPIO pins at once.

Parameters

mask	Mask of GPIO pins to configure. A bit set to 1 configures this pin. A maximum of 32 pins can be configured at once. The real number depends on the hardware and the driver implementation.
mode	GPIO function, see L4vbus_gpio_generic_func for generic functions. Hardware specific functions must be provided in the lower 8 bits.
value	Optional value to set the GPIO pins to if they are configured as output pins

Returns: 0 if OK, error code otherwise

Definition at line 166 of file vbus_gpio.

References L4vbus::Device::_bus, L4vbus::Device::_dev, and l4vbus_gpio_multi_setup().

Here is the call graph for this function:

The documentation for this class was generated from the following file:

l4/vbus/vbus_gpio

Data Structures

Public Member Functions

Additional Inherited Members

Detailed Description

Member Function Documentation

◆ config_pad()

◆ get()

◆ pin()

◆ set()

◆ setup()